| Model |
|S-35-5 ||S-35-12 ||S-35-15 ||S-35-24 |
|DC output voltage ||5V ||12V ||15V ||24V |
|Output voltage error(Note2) ||±2% ||±1% ||±1% ||±1% |
|Rated output current ||7A ||3A ||2.4A ||1.5A |
|Output current range ||0-7A ||0-3A ||0-2.4A ||0-1.5A |
|Wave and noise(Note3) ||75mVp-p ||100mVp-p ||100mVp-p ||100mVp-p |
|Inlet stability(Note4) ||±0.5% ||±0.5% ||±0.5% ||±0.5% |
|Load stability(Note5) ||±1% ||±0.5% ||±0.5% ||±0.5% |
|DC output power ||35W ||36W ||36W ||36W |
|Efficiency ||70% ||76% ||78% ||78% |
|Adjustable range for DC voltage ||±10,-5% ||±10% ||±10% ||±10% |
|AC input voltage range ||85132VAC/170264VACselected by switch |
|Input current ||0.85A/115V 0.45A/230V |
|AC impulse current ||Cold-start current 18A/115V 36A/230V |
|Leakage current ||<0.5mA/240VAC |
|Overload protection ||105%150% Type: current limiting; Reset: auto recovery |
|Over-voltage protection || |
|High-temperature protection || |
|Temperature coefficient ||±0.03%(050) |
|Setup rise hold up time ||200ms,100ms,30ms |
|Vibration ||10500Hz,2G 10min./1cycle,Period for 60min,Each axes |
|Withstand voltage ||Input and output intermal:1.5KVAC,Input and enclosute:1.5KVAC,Output and enclosure:0.5KVAC |
|Isolation resistance ||Input and output interval,Input and enclosure,Output and enclosure0500VAC/100M Ohms |
|Working temperature and humidity ||-10+60,20%90%RH |
|Store temperature and humidity ||-20+85,10%95RH |
|Overall dimension ||129*98*38mm |
|Weight ||0.4Kgs |
|Safety standards ||Meet UL 1012 requirement(Not apply for the mark) |
|EMC standards ||Meet FCC Part 15J Conduction Class B |
1.The testing condition for the parameter above is:230VAC input, rated load,25 70%Rh,Humidity
2.Error,include the setting error, line stability and load stability.(Note:5)
3.Wave test:adoptingA12double wire for 20MHz,and 0.1uF&uF capacitor short-circuit for interrupting
4.Inlet voltage stability test: when is over load, the lowest voltage of inlet is representative to the highest voltage.
5.Load stability test: The load is from 0% to 100%,Others 60%.
6.C2311must be knocked down.
Contact us if you need more details on Switching Power Supply. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Switch Power Supply、LED Switch Power Supply. If these products fail to match your need, please contact us and we would like to provide relevant information.
Switching power supply fault check
Most peripherals now use switching power supplies for voltage conversion. Although the switching power supply has the characteristics of small size, high working efficiency, and good voltage regulation effect, since the switching power supply is directly connected to the commercial power, the change of the commercial power...
High-frequency switching power supply parallel sharing system
Modularization is the development trend of switching power supplies. Parallel operation is an effective solution for large-capacity power supply products. The N+l redundant power supply system can be designed to achieve capacity expansion. This system is a high-frequency switching power supply (1000A/15V) intelligent module...
The wide application of switching power supply modules makes the market highly competitive
Switching power supply has been widely used in the MTD2002 industrial field for its advantages of high efficiency, energy saving, small size and light weight, and has become an important basic product in the industrial field. At present, most of the major enterprises in China's industrial switching power supply module...
How to use LED switching power supply
As the heart of electronic equipment,switching power supply plays a crucial role in the safe and reliable operation of electronic equipment.So how to use LED driver is the most important. 1.Before using the power supply, determine whether the input and output voltage specifications match the nominal value of the power...
Product Categories : Single Output Switching Power Supply
Items in Inquiry Basket
Products( 0 )